TLR 22 4.0 carpet setup (SCVRC)

Hello everyone,

This week I would like to share a new carpet setup by TLR’s very own Frank Root. Frank made the trip to SCVRC (newly transformed over to a carpet track) back in February for “The Series” event round three. Frank grabbed the TQ and the win at this event and he has posted his setup. If you're looking to do some carpet racing with your TLR 22 4.0 this is a very good starting point for any carpet surface.                               

  Setup Frank Root SCVRC

JR
#22empire

TLR Slipper adjustment

Hello everyone,

This week, I would like to talk about how to adjust your slipper on your TLR vehicles. The first and most important is making sure that the slipper is set loose and your diff is tight and broken in correctly before you attempt to find the correct setting for your slipper. If the slipper is too tight, you could cause damage to your diff even before you hit the track. After making sure your slipper is loose, hold both rear tires with your radio and car on and give the car a quick stab of the throttle and you should be able to hear the slipper slip. Keep tightening the slipper at half turn increments until the front tires come off the ground about an inch. This should be a good starting point for most tracks.

               

JR

#22empire

22 Spring Cup Modification

Hello Everyone,

I thought I'd share a very easy modification I came up with to help get the 22 vehicles more adjustment for ride height.  Especially with the 22 4.0, recent setups have a lot of the race team running cars around 1500-1510g, making lower ride heights close with fully stock parts.  This modification is simple, quick and requires no additional parts.

Step 1 - Remove your rear spring cup.  The material that will be removed is shown in the image below marked with a silver sharpie.  Essentially, we are going to remove the lip that usually rests atop of the shock eyelet, which allows the spring cup to slider down a few more millimeters.

Step 2 - Remove the material from the spring cup, using a 6.2mm drill bit, either with a drill or a Dremel.  You can also use a grinding bit.

Below is an image of a modified spring cup on the right, with a stock spring cup on the left.

Thanks guys!

Zeke Ballinger

New 8th Scale 5mm Rod Ends

Howdy Folks,

     I wanted to just make a quick post here on a new item we released a few weeks ago now.  These are TLR344015 5MM Moly Rod End Set:8B, 8T.  These can be used on any of our 8th scale vehicles using the 5mm turnbuckles.  These are out of a new material and are more free than the original LOSA6047 and will not need to be squeezed when the temperature changes.  Thats it for today gents!

Good luck out there to those attending the nitro challenge.  We will be out there under the tents so if you need anything or have any questions or just feel like saying hello, please do.

New 22-4 2.0 Setup

Hello Racers!

During our recent testing in preparation for Reedy Race, team driver Reno Savoya got all of our 22-4 2.0s' way more dialed in with an outside the box setup idea.  After showing us how good it was with his speed on the track while running at Travis Brock's SDRC Raceway, Dakotah and I both gave it a try and we instantly knew it was an improvement for the car - and pretty much the rest of the team switched over during the Reedy Race.  What was this magical setup change... glad you should ask!

Reno deep in wrench mode!

We've found that running a ball diff in the rear, paired with a gear diff in the front, was a great way to maximize how the car drives.  The gear diff in the front allows the diff to 'free up' off power to help the car turn in and rotate quicker, then 'lock up' on power to pull the front end out of the turns.  The ball diff in the rear, gives the 22-4 the stability, consistency, and predictability of a ball diff setup.  Really, the front gear diff and rear ball diff setup gives you the best of both worlds, without the negatives of either.  Even the ball diff life-span in the rear is improved with the gear diff up front.

So here are some details we 'fine-tuned' after making this change.  With the ball diff adding consistency in the rear, we found that we could run the front diff with thinner oil to improve steering.  We're pretty much all running 30,000cs oil in the front diff, so I'd suggest starting here.  If you want a little less aggressive steering, try moving up to 40,000cs.  For the ball diff, we've been running it set very similar to a 2wd 'normal' diff setting, about 1 full rotation.  We have found that running the diff too tight can make the rear feel a little less consistent, almost like a solid axle.

If you have the 22-4 2.0, you'll need the parts listed below to try the ball diff setup in the rear:

1x   TLR232017  Outdrive Set: 22-4
1x   TLR232026  Diff Service Kit, Tungsten Balls: 22-4
1x   TLR237000  5x8x2.5mm Bearings (2)
2x   The black bearing spacers that come with the 22-4 2.0 kits, in the tuning parts bag*

* These can also be found in TLR231043 and TLR231044

Give this setup a shot, we're confident you'll like it!

Race on!
Frank

Martin Harrison winning TLR 8IGHT E 4.0 Setup

Hello everyone,

 Last weekend I attended the Southern Indoor Championship in Autaugaville, AL. a Racetime Entertainment event with over 500 entries. TLR was a sponsor of this great event and we had several drivers in attendance all having awesome results. TLR driver Martin Harrison took the TQ and the win in 40+ Ebuggy this year and I’ve asked him to share his TLR 8ight 4.0 setup with the TLR blog mates. Next on the schedule is Motorama in a couple of weeks hope to see everyone there!
Martin Harrison's TLR 8IGHT E 4.0 setup Martin used 37.5 front and 32.5 rear shock oil

JR
#8realm

Turf 22-4 2.0 setup (Beachline raceway)

Hello everyone,

Last weekend was the first JConcepts SuperCup of 2018 hosted by Beachline raceway with a great turn out of 240 entries. Beachline is in Cocoa, Florida about two hours from Tampa where I’m located, and is the only turf track in the state. I had a very productive weekend in both 2wd and 4wd but I had the most success in the 4wd class with my TLR 22-4 2.0 bringing home the win with a last lap pass. Here is the link to my setup: TLR 22-4 2.0 Beachline setup Photo credit: JConcepts

*I forgot to add that I used +3.5 rear hubs in the setup sheet

JR
#22empire